Own leather bracelet. DIY leather bracelets: how to make an unusual accessory

We continue the topic of hande-made bracelets again. We make leather ones for this one.

Once again, it's time to stretch our hands a little, exercise our imagination, use the creative spark within us, and make something with our own hands. And not even something, but trendy leather bracelets. What is great about these bracelets is that you can wear them with anything, especially ethnic clothing. In addition, there is a huge variety of different shapes, colors and options, so you can always choose a leather bracelet to match your outfit. Well, to describe how good they look on the hand is not even worth it.

Photo: www.ispydiy.com, www.trinketsinbloom.com,

So, let's proceed directly to the process of creating bracelets.

DIY wide leather bracelets

You will need:

Leather straps (leather straps with a clasp at the end)
. Ribbons
. Metal spikes
. Threads
. Super glue

DIY leather bracelets

You can just glue a narrower piece of ribbon on the bracelet and add some spikes.
And you can attach spikes and entangle them with a bright thread (yellow, for example).
You will get 2 wonderful bracelets.

How to make leather bracelets photo

A couple more options for the creative process. You will need:

- leather laces - you can use thin leather ribbons
- floss threads
- glue
- scissors
- scotch
- needle

Step 1
Measure your wrist by wrapping the leather cord around your wrist loosely twice, then add an extra 10cm to tie. Glue one end of the leather cord to the surface so that it does not move and, stepping back about 5 cm from the edge, drop glue on the leather cord and attach your first floss color to it.

Step 2
Continue winding the floss around the leather cord until you've made a strip of the width you want, then cut off the rest of the thread, securing the end to the bracelet.

Step 3
Take a different color of thread and do the same procedure with it again. Continue doing steps 2 and 3 until you have made about 5 cm of different colors.

Step 4
When you are done wrapping, take the needle and pass it under yours. If you want, you can add a small drop of glue to make sure your floss doesn't come off.

Step 5
Tie the end of the lace closest to the wrap around the other end of the lace. Make a simple knot. The knot should be strong, but the leather cord should be free to go back and forth, to slide through it.

Tip: Before tying a leather cord, dampen it a bit and remember to make it softer and easier to tie. This will also help make a strong knot.

Step 6
Leaving at least 10 cm on the other side, repeat steps and 1, 2, 3, and 4 again.

Step 7
When you've finished wrapping your bracelet on the other side, tie off the loose end again on the other side.

You will get wonderful multi-colored bracelets.

DIY leather bracelets

Well, now more complex options.

You will need everything that is at hand: leather laces and strips, beads, chains, glue, threads.

1. Bracelet with beads. Take 2 laces, put beads between them and attach the beads to the laces, passing the threads through them and wrapping the laces with these threads.

2. Multi-strand bracelet with beads. Just take a few suede threads, a couple of clasps for the ends, and beads with beads through which your threads can pass through. String your beads and beads on strings, tying the thread after each with a knot. Fasten the clasps at the ends.

3. Braided bracelet with beads. This is also the easy way. Just start braiding suede threads, adding beads here and there, fasten the fasteners at the ends, and you're done. Such a woven bracelet can also be made with a chain. Just add a thin chain instead of one of the threads and start braiding.

Don't stop your imagination. You can make your own versions and variations. The main thing is that you do not have to buy such wonderful bracelets in the store.

Woven leather bracelets are a versatile accessory. Leather bracelets have been in trend for several fashion seasons. Bracelets come in a variety of colors and shapes. They can be both female and male.

At the same time, a leather bracelet, as in the photo, can look both elegant and extravagant. It all depends on the pattern of weaving a leather bracelet, which you can make yourself. How to learn to weave bracelets? More about this in our step-by-step master class with photos and videos.

You will need small pieces of leather for this. They may not be new.

Pigtail weaving is one of the simplest and most beautiful solutions for a leather bracelet that will suit both men and women. A pigtail can be weaved in several ways.

Simple DIY leather bracelets:

It will take a strip of leather the length of the circumference of the wrist plus 2 centimeters. The width of the leather bracelet can be any.

You can try to make a narrow bracelet about 2-3 centimeters. Using a hole punch, you need to make holes at the ends of the workpiece. Laces can be passed through these holes, or a metal button can be fixed. This is a universal blank for a bracelet.

Such a blank can also be decorated with rivets or patterned holes. A master class on making a leather bracelet offers to learn how to make an unusual weaving with a pigtail. The unusual thing is that the pigtail will not weave from separate parts. This weaving is not cut, but quite simple.

Learning to weave a leather bracelet: a step by step photo lesson

1. Using a ruler, divide the width of the bracelet into three equal parts. Make marks, draw with a knife, making 2 cuts along. You will get 3 strips, from which a pigtail will weave. 1 strip - left. 2 strip - central. 3 strip - right.

2. Fasten one end of the bracelet. This makes it easier to work with weaving. You can put it under the load or tie it to something. You can also use masking tape and glue the end of the bracelet to the table.

3. Raise the end of the bracelet, pass it through strips 2 and 3. Lower it down (moving away from you). The strips will begin to wrap (as needed, they will straighten out at the very end). Lower the end of the bracelet down.

4. Interlace the left strip and the central one. Weave the right strip through the center strip. Skip the end of the bracelet between 1 and 2 strips. This should straighten out the wrapped strips.

5. Weave the right strip through the center, weave the left strip with the center strip. Pass the end of the bracelet through 2 and 3 strips. The strips will curl up again.

6. Repeat steps 2 and 3 until the bracelet is complete.

Different skin behaves differently. Much depends on its thickness and softness. But in any case, the last step should be straightening the bracelet.

Some bracelets are tighter, some are looser. It does not depend on the technique of weaving, but how plastic the skin itself is. Having mastered one weaving option, you can further learn to weave bracelets using different techniques with your own hands.

The scheme that we have given will become the basis, even for beginners it is easy to learn how to weave leather bracelets using it. A leather bracelet is not suitable except for a business dinner or going to the theater. For other cases, you can actively use leather accessories. They are especially recommended for country style, casual, ethnic and many other styles.

An obsolete jacket, an old bag or a piece of leather lying around in the bins are the perfect material for creating a stylish piece of jewelry.

In this master class, you will learn how to make a leather bracelet with your own hands from a tin can and a small piece of soft leather. For decor, you can take any stone that you have, buy a natural mineral or use an imitation made of plastic or glass. Here, amber plays the role of a decorative element.

Preparation of materials and tools

To turn a tin can, a damaged piece of amber and several small pieces of leather into a massive and stylish women's bracelet, you will need the following tools and materials:

• pieces of soft and thin natural leather;
• amber;
• transparent universal glue "Dragon";
• tin can from canned food;
• metal scissors;
• scissors;
• ball pen.

If there is no stone, you can make it from polymer clay, for example, according to.

Step by step photo tutorial

First, make a metal frame for a leather bracelet. Tin from a can of canned olives or olives is best suited, it is thinner and at the same time holds its shape well.

Cut out a rectangle with metal scissors and trim the corners by rounding them.

Give the frame an oval shape. Try on by hand and, if necessary, reduce the length.

Make a lining from the wrong side. To do this, use a ballpoint pen to trace the outline of the frame on a piece of leather. For this stage, you can take material with defects, for example, with uneven coloring or more rough.

Cut the backing with scissors, leaving a one centimeter allowance around the entire perimeter. Spread the entire wrong side with a transparent universal glue "Dragon" or "Moment".

Glue the backing on the inside of the frame. Bend the allowance to the outside, and make folds from excess skin at the ends. Please note that the skin, smeared with glue, stretches well. Therefore, on the edges of the blank for a leather bracelet, pull it slightly.

Let the glue dry for a couple of minutes and cut the folds with scissors as close to the plane of the bracelet as possible.

Decorate a women's bracelet with fine beautiful leather and stone. To do this, take a segment three times larger in area. Liberally apply colorless glue to its middle and to the stone.

Mark approximately the center point on the product and start gluing the skin from this place. Apply amber to the same place. While the glue is still wet, form folds around the stone with your fingers. Drapery cover the place of the chip.

Add glue to the remaining surface and glue the leather decoration all over the outer surface of the bracelet.

Shape the decorative drapery to your liking. Bend the edges inward. If possible, try to keep as few wrinkles as possible on the inside of the product. Cut off the excess.

After a couple of minutes, cut off as much as possible all the folds of the skin on the inside of the bracelet.

Cut out another piece for the underside. Measure the workpiece by applying it to the surface.

Apply glue to the entire surface of the part.

Gently glue the part on the inside, thus hiding the edges bent from the outside. Start gluing from the ends of the product.

After the glue has completely dried, give your leather bracelet its final shape by squeezing it with your hands for a few seconds into a small oval.

A thin metal base will keep the shape and give elasticity to the structure. Using this technique, you can decorate with your own hands women's leather bracelets and other elements, such as shells, sea stones and glass, metal parts and even interesting beads. In any case, your masterpiece will be unique.

We also have a do-it-yourself leather bracelet, but we use the cord weaving technique. If you still have some skin left, decorate for yourself or as a gift. It is very exciting to create, as a result you always get an unusual souvenir or jewelry.

Other instructions for making jewelry in different techniques. Follow us on social networks to get news about publications, see crafts and other participants, and sell yours.

Handmade leather bracelets are another type of jewelry that has a popular position in modern women's and men's fashion. Let's talk about examples and ideas of such bracelets today. In the master class, we will assemble a stylish bracelet from thin leather laces and decorative connecting rings.

Leather bracelets are very diverse in their assembly. Masters use both thin and dense skin in their work; leather cords; stripes; flaps, etc. Leather elements can play a major role in the decoration, acting as the only base or some separate decorative fragment, decorated with beads, beads or pendants. Consider a few examples of leather bracelets.

Leather bracelets in the form of one or more stripes or cords, decorated with a decorative lock, separator beads or a pendant:

Braided bracelets made of leather cords, decorated with beads.

Leather bracelets with applied or embossed inscriptions or patterns.

Figured bracelets made of leather, with the help of cutting.

Men's leather bracelets decorated with rivet beads or metal links.

Leather bracelets decorated with embroidery.

Volumetric leather bracelets with a textured texture, decorated with accessories for jewelry.

Fine leather bracelets in the shape of a gathered accordion.

Bracelet made of dense leather, with a decorative three-dimensional element in the form of a leather flower, with the effect of toning.

Leather bracelet on a metal blank.

A master class of a bracelet made of leather cords and decorative connecting rings.

Accessories:

Leather cord 1 meter

Terminal clamps pcs

Decorative connecting rings 3 pcs

Carabiner lock 1 pc

Small connecting rings 2pcs

Instruments: Scissors, pliers.

Assembly:

We cut 6 leather cords, put them in the end clamp and clamp the teeth of the end clamp with pliers. For reliability, before clamping, you can apply a few drops of glue to the trailer.

We lay out the cords on the desktop as shown in the photo below. We retreat from the edge of the bracelet about 5 cm. We draw a decorative ring into the central two cords.

Under the ring, we put the side cords on the central cords, as if braiding a simple braid, and then bring the central two cords back up so that they are on top of the decorative ring.

Again we draw a decorative ring through the central cords.

Weave a braid under the ring and again bring the central cords up.

We repeat the steps one more time.

We fix the remaining edge of the bracelet as at the beginning, using the end clamp. We add a carabiner lock through small connecting rings.

The bracelet is ready!

Anna Pavlenko

Leather bracelets are versatile accessories that have been in fashion for several seasons and remain popular. Women's baubles are woven and flat, because the preferences of girls are different. But many agree that handicrafts are interesting and look much more original than those sold in stores.

They come in different colors, sizes and shapes, you can use a wide variety of weaving patterns and a huge selection of methods for weaving leather products.

Such products can look both elegant and extravagant. It depends on the weaving method. How to learn to weave leather bracelets? First you need to purchase small pieces of leather and cut them into strips. There are many weaving patterns, but it is better to start with the simplest ones.

Braid bracelet

This is one of the simplest and most elegant solutions for a leather bracelet.

Weaving products can be done in several directions.

1. Wrap a long leather strap around your wrist and add 2 centimeters to this length, this should be enough. The width of these strips can be different. You can try to weave from narrow strips with a width of 1.5 to 3 centimeters;
2. Using a hole punch, make holes at the ends of the strips;
3. In the holes, you can fix a metal button or thread laces through them. These are standard ways to fix the ends of products;
4. This blank can also be decorated with rivets or patterned holes;
5. Then, you should weave a traditional braid of three strips.

You can weave a slightly unusual braid in a different way

1. Using a ruler, a wide leather ribbon should be divided into three parts of the same width and evenly cut along, but not completely. The ends can be decorated with decorative buttons;
2. As a result, you get three stripes, from which you need to weave a braid: No. 1 - on the left, No. 2 - in the middle, No. 3 - on the right;
3. You can start weaving. One edge of the bracelet must be passed between strips No. 2 and 3 and lowered down. As a result, the stripes will be twisted;
4. Then you need to pass the edge of the bracelet between strips No. 1 and 2 and lower it down;
5. We repeat the previous steps one by one until the bracelet is ready;
6. The last step should be to straighten the bracelet.

Different types of leather behave differently depending on its softness, dressing and thickness. Some bracelets will turn out tight, some more loose, it all depends on the technique and quality of weaving, as well as on the skin and its plasticity.

If you have mastered one version of leather weaving, you can continue to learn how to weave bracelets using various techniques.

Baubles with embroidery

You can add a leather ribbon decorated with appliqués, colored threads or interesting studs to a thin woven bracelet.

This can be a strap about 3-4 cm wide. You can buy special leather for baubles or take an old belt, bag or upper part of a soft old boot.

Leather can be black, it will contrast beautifully with bright embroidery, brown leather also looks beautiful and stylish.

You should also stock up on metal embellishments, such as heart-shaped ones, which can be purchased at any craft or scrapbooking store.

You can embroider with thick stitches of bright thread or decorate the product with decorative elements. Such a product can be fastened with an ordinary button.

How to weave a bauble out of leather

You will need:

• narrow strips of leather or leatherette of any color;
• thick cord or wire;
• lighter;
• large lock with a hook;
• scissors;
• Super glue.

How to weave a bauble:

1. Cut a piece of wire or lace 15 cm long;
2. Scorch the ends of the lace with a lighter or other fire;
3. Make a loop;
4. Using glue, you need to attach the loop to the surface on which you will weave the bracelet;
5. Insert a leather cord under the wire;
6. Braid the wire like a double flat knot used in the macrame technique;
7. Repeat until you have tied the entire cord. Knots can only be placed on one side or on two;
8. Cut off excess cord;
9. Glue the lock at the end, hiding the ends of the wire and both ends of the leather strip underneath.