Flowers from plastic bottles: large daisies. DIY bouquet of daisies from a plastic bottle and disposable cups

Chamomile from a plastic bottle already used in the house - budget beauty! Handicraftsmen make countless flowers from plastic bottles. One of the beautiful and realistic flowers is the chamomile. Large daisies from bottles are made to decorate flower beds, front gardens, and summer cottages. And with small ones you can decorate the interior of an apartment or house, and you can also make a composition for a gift.

Below are step-by-step instructions for making both small and large daisies.

Making small daisies from a plastic bottle with sharp petals

These little beauties of daisies look great in a bouquet on the windowsill in an apartment. You can also decorate a gift with these daisies or give them yourself.

To make these daisies you will need:

• Small white bottles (for example, from the drink "Actimel")
• Yellow lid
• Wire

For one chamomile you need three bottles. The neck of the bottle is cut off, leaving a bend, from which future petals will bend beautifully. Next, the bottles are cut into strips along the entire length, not reaching the bottom 1 cm. Each strip must be sharpened with scissors and bent to the sides. Then you need to make slits or holes in the bottom. Through the slot, place all the petal blanks on the wire, the end of which must be clamped with a loop. Apply glue to the bottom of the first blank, so that the future chamomile falls down. Pour glue into the middle of the blanks and put on the lid. Spread the petals. The chamomile, made yourself from a plastic bottle, is ready.

Let's try to make a version of delicate daisies with rounded petals

These flowers can be used to decorate both the interior of the apartment and the area in front of the yard. The densely planted daisies in front of the house resemble a chamomile field.

For the craft you will need:

• Clean plastic bottles (white, green, yellow)
• Candle (lighter)
• Scotch
• Marker
• White paper
• Wire
• Scissors, awl, compass, ruler, pliers

Petals.

Cut off the neck and bottom of the white bottle. Cut the bottle in half and lengthwise to create pieces of plastic. On a piece of white paper, using a compass, draw a round template, the size is adjusted to fit the pieces of plastic. Transfer the template to plastic and cut it out. Draw strips on plastic circles and cut, not reaching the middle 0.5-1 cm. Round the edges and bend them a little over the fire.

Leaves, sepals and stem.

Draw a leaf and sepal on white paper, cut it out and transfer it to a green bottle. Chop the leaves and sepals. Cut the rest of the bottle in a circle into a thin long strip. Wrap the strip around the wire and burn it a little over the fire.

Core.

Cut one convex part from the bottom of a yellow bottle and bend it slightly over the fire

All preparations are ready. The flower is easy to assemble: put the sepals on the wire, then the white petals, round the end of the wire with pliers and glue the yellow center on top. Glue the leaves to the stem as well. Ready!

The flowers come out in medium size and look beautiful in front gardens or flower beds.

Materials:

• Three plastic white bottles
• Yellow cap
• Wire

Technique.

Cut the bottles in half at the expansion point. Cut off the necks of two bottles. Cut all the blanks into petals and round the edges. Insert two bottles alternately into a bottle with a neck, pierce it with an awl and insert a wire, secure with glue. Screw the cap onto the bottle with the neck. Straighten everything out. Chamomile made from plastic bottles!

These daisies turn out to be very large. They decorate personal plots, flower beds, and front gardens. You can see such flowers from afar.

Materials and tools:

• Large white plastic bottles
• Plastic plate
• Strong wire
• Candle or lighter
• Scissors, knife, awl

Step-by-step instruction.

Cut off the necks and bottoms of the bottles. Cut lengthwise and cut petals from these blanks, shape them by slightly bending them over the fire. It’s better to take a yellow plastic plate; if you don’t have one, then you need to paint it first. Use a knife to make holes on the edges of the plate and insert the prepared petals into them. From the inside of the plate, carefully burn the inserted edge of the petal with fire. This will prevent them from falling out. Make a hole in the middle of the plate and thread a wire through it, imitating the stem of a flower. Chamomile is ready!

From the same materials, everyone will get their own beautiful daisy, with its own special twist, which will definitely fit into either the interior of the apartment or the design of the garden plot. And a creation made with your own hands will always please the eye.

Each master uses his own tricks for making daisies from plastic bottles, and some are willing to share them. You can learn a few little tricks from the video master classes:

Video on the topic of the article

Flowers made from plastic bottles perfectly complement real, living vegetation on the site. It is not necessary to make them life-size; on the contrary, it makes sense to make them much larger: this way they will look more impressive. You can also make small flowers, but in this case there should be a lot of them - whole curtains or flower beds.

Chamomiles from plastic bottles

You can make charming daisies from plastic bottles quickly and easily. You don't even have to paint them if you use opaque white plastic dairy bottles. The height of the flower petals will be equal to the height of a plastic bottle, which means you will need several empty containers.

In principle, daisies can be made from bottles of a different color, and then simply paint the petals with acrylic paint (it’s more convenient to use a spray can).

Stages of work on making chamomile from plastic bottles

1. For one flower you will need 3 plastic bottles.
2. Cut the bottles approximately in half crosswise. Set aside the lower parts - they will not be needed for the garden craft.
3. Cut off the necks of the top two pieces.
4. Cut out the petals without cutting all the way through. Try to make the petals rounded at the ends.
5. Place two top parts without a neck on the top of a plastic bottle with a neck. There were a lot of petals - in three layers! By the way, the more magnificent the flowers from plastic bottles, the better they look.
6. Bend the petals upward, forming a beautiful blooming flower.
7. Screw the lid on the neck of the garden craft to create the center of a flower. You can also make a “natural” yellow center using a Kinder Surprise box or other available material of a suitable color. True, in this case, you will have to attach it: the easiest way to do this is with wire.
8. Secure the chamomile head to a tall stem. This could be an iron rod wrapped in a strip cut in a spiral from a green bottle. If you heat it a little over a fire, the plastic will begin to melt and “grab” well with the rod.

Flowers made from plastic bottles are simple and original crafts for the garden that you can make with your own hands without spending a penny on materials. You can make flowers from different types of plastic bottles. But first, be sure to decide on the style, because if there are many different colors in one area, the result will be colorful and not beautiful. If you “plant” many flowers of the same type, for example, daisies, you will end up with a “chamomile meadow” that you can’t help but admire.

MORE CRAFTS AND FLOWERS FROM PLASTIC BOTTLES.

We all have a soft spot for flowers. Men give “a million scarlet roses” to the fair half of humanity, confirming their feelings. Children give gifts to mothers and grandmothers on March 8th. This is not enough for many women, and they create artificial crafts, armed with paints, scissors, and glue.

All these examples are quite simple to implement.

Thus, a huge number of the most amazing crafts made from plastic bottles have appeared. We want our flowers to delight others constantly and regardless of the weather, soil, watering and lighting of the garden. This means that we will consider crafts that best meet the following requirements:

• easy to manufacture;
• do not require painting, at least complex;
• fit harmoniously into the surrounding landscape.

Ordinary bottles can easily turn into fabulous beauty

Throughout the article there are descriptions of master classes on the most successful flower crafts for the garden. After studying these examples, you will be able to make any flowers for the garden with your own hands.

Simple and touching flowers made from plastic bottles without painting

Of course, first of all, I want to make daisies for the flowerbed. They can be made from parts or whole white bottles. A yellow lid or the bottom of a brown container is suitable as a core. Plant leaves can be made from green containers. Stems can be made of wire, pipe, rebar or wood. The latter should be painted green.

Let's look at making chamomile from three white bottles step by step:

Lily of the valley from white bottles for the garden also turns out great. Depending on the availability of containers, the upper or lower parts of the bottles are used. Lily of the valley petals can be made round, sharp, or bent. Depending on the material and diameter of the stem, the buds are secured with screws or wire. It is convenient to make lily of the valley foliage from a five-liter eggplant with the neck down. The leaves will have to be painted.

Dandelions are made in different ways. White dandelions can be made from bottles of the same color. To do this, it is convenient to use the upper parts of the container, cut in the form of sharp petals. Each part is attached to a wire of the same length to a common center. The result is a light white ball.

A group of transparent bottles can be attached to a common center. You will get a large dandelion. If you create a spatial structure with several centers, you can make a huge dandelion.

Colored dandelions made from containers of the appropriate color look very interesting. Let's look at the step-by-step instructions for making a handsome brown man:

Making charming buds using a magic candle

A candle flame works wonders on plastic bottles. Look at the examples in the photo below. Together we will make just one flower, and you can repeat any other with your own hands.

Master class on making a flower using a candle:

1. From one container we prepare seven fragments, as in the photo below. The largest measures 8x8cm, the smallest - 3.5x3.5cm. We make holes in the center of the parts.
2. We melt the edges of the parts using a candle flame. Keep the part to the side of the flame. Smoky areas are easy to clean. Do not allow the plastic to catch fire.
   
3. For the stem of the craft, we will prepare insulated copper wire. The end of the wire must be stripped and bent 5-10mm.
4. To cover the stem, cut out a ribbon 7-12mm wide from a green container.
   
5. We insert the end of the tape into the bend of the wire. We wrap the ribbon around the stem and melt it in a candle flame.
6. The result is a green flower stem. The end of the wire is cleared of 20mm of insulation.
7. We prepare a template from paper for making foliage in accordance with the drawing.
8. Another template will be needed for the leaves next to the bud.
   
9. We cut out the foliage for the cutting according to the template.
10. We make leaves under the bud according to the template.
11. Melt the edges of the leaves under the bud. Look at the photo to see how it turned out.
12. We melt the leaves for the cuttings along the edges, and twist the strips of plastic connecting them over the flame.
    
13. You should get a twig like in the picture.
14. Using a flame, wrap the base of the branch around the stem. We put leaves under the bud on the protruding part of the wire.
15. First, we put the largest fragment of bud petals on the wire.
    
16. We sequentially put on the petals of the bud as their size decreases. We try to unfold the petals so that they cover the gaps between them. We bend the end of the wire with pliers so that the petals do not fall off. The flower is ready!

We make flowers for flower beds, ponds and fence decorations; we use paints and large bottles

Flowers from plastic bottles for a pond are very popular. In the simplest case, you can make a water lily from the bottom of a white bottle, as shown below. The core of a flower can be easily imitated with a yellow cork.

We will look at a master class on making a more complex flower for a pond:

1. First, let's prepare three parts of lily petals from white containers as shown below. The neck of the plastic bottle should pass through the holes at the top along with the belt below it. You will also need a yellow strip 25mm wide, cut in 3mm increments to a depth of 15mm. From the top of the yellow bottle we will make a part for the core of the bud with eight petals.
   
2. We process the strip for the core over fire. Narrow fragments should melt and bend inward.
   
3. We also melt the petals of the bud core holder using a candle.
4. The workpiece should look like we see below.
   
   
5. We roll up the strip with folds and insert it into the body of the bud core.
6. To assemble the water lily, we will need a lid from a container with a wide neck. We cut a hole in it through which the neck of a regular container will pass.
7. We turn the yellow core over and put lily petals on it. We rotate them so that they do not coincide with each other. We put a large lid on the neck. We hook a fragment of the inner padding of the bud core to the edge of the neck.
   
8. We wrap the lid.
   
9. This is what a fully finished water lily for a pond looks like.

A bright sunflower will serve as a worthy decoration for both flower beds and vegetable gardens. As you can see, it can be made in different ways. Sunflower petals made from brown containers look good. The core can be a disposable plate.

The simplest thing is to use a 5 liter plastic bottle. A blank is cut out of it, as shown below. The petals will have to be painted with yellow paint.

Now we will tell you how to make a wonderful chamomile from plastic bottles with your own hands, an exclusive one at a minimum cost.

For this job you will need:
1) Empty plastic bottles in three colors: white, yellow and green;
2) Candle and matches or lighter;
3) Thin marker or felt-tip pen;
4) Good sharp scissors;
5) Shilo;
6) A piece of thick wire, approximately 25-30 centimeters long;
7) A sheet of white paper;
8) Ruler;
9) Compass;
10) Superglue (or any other);
11) Round nose pliers;
12) Scotch tape.

So, we can begin.

First you need to cut an even part from the white bottle and divide it in half. Using a compass, estimate the size of the circles that will fit on a given piece of plastic, you need two of them, transfer this size to paper and draw a template.

Cut this circle out of paper and attach it to the plastic, circle it with a marker and cut it out.

Without cutting to the middle of the workpiece, make frequent proportional cuts and additionally round each petal.

If you are not sure what you will get by eye, make a mark using a ruler, divide the circle into 16 parts, then round each of them to make petals.

Set the flowers aside, time to work on the leaves.

Randomly draw a proportional piece of paper on paper and cut it out. Place your template on a piece of green bottle, trace and cut out two leaves and an arbitrary star for the cup.

Now you need to cut a green thin strip of about 5 millimeters for the stem, half a meter will be enough.

Cut a small circle from a yellow bottle for the core, and make small frequent cuts along the edges. You need to cut off one convex edge from the bottom so that it can cover the core almost completely.

Now all our blanks are ready, it’s time to give them a rounded shape so that the flower looks like a real daisy. To do this, you need to heat the white blanks, core, leaves and calyx over the fire and slightly bend them. Light a candle. Carefully bring the pieces to the fire to lightly melt them.

You need to make a stem. Take a thin green strip and wire, bringing it to the fire, gradually wind the plastic onto it, leaving about a centimeter of wire free. Heat the edges more to ensure maximum fixation.

All that remains is to secure it. Place the cup, petals and core on the remaining tip of the stem, bend the wire with pliers,

Now glue the convex yellow piece. Place the leaves on the stem; you can attach them with tape or glue.

Your work of art is ready, everyone will be delighted with such a gift. Everything is simple, easy and elegant!

The final look of the craft.

In addition to various flowers, our website also presents crafts for children, for example, an airplane from a bottle, which a child can easily make.

Chamomile from a plastic bottle already used in the house - budget beauty! Handicraftsmen make countless flowers from plastic bottles. One of the beautiful and realistic flowers is the chamomile. Large daisies from bottles are made to decorate flower beds, front gardens, and summer cottages. And with small ones you can decorate the interior of an apartment or house, and you can also make a composition for a gift.

Below are step-by-step instructions for making both small and large daisies.

Making small daisies from a plastic bottle with sharp petals

These little beauties of daisies look great in a bouquet on the windowsill in an apartment. You can also decorate a gift with these daisies or give them yourself.

To make these daisies you will need:

• Small white bottles (for example, from the drink "Actimel")
• Yellow lid
• Wire

For one chamomile you need three bottles. The neck of the bottle is cut off, leaving a bend, from which future petals will bend beautifully. Next, the bottles are cut into strips along the entire length, not reaching the bottom 1 cm. Each strip must be sharpened with scissors and bent to the sides. Then you need to make slits or holes in the bottom. Through the slot, place all the petal blanks on the wire, the end of which must be clamped with a loop. Apply glue to the bottom of the first blank, so that the future chamomile falls down. Pour glue into the middle of the blanks and put on the lid. Spread the petals. The chamomile, made yourself from a plastic bottle, is ready.

Let's try to make a version of delicate daisies with rounded petals

These flowers can be used to decorate both the interior of the apartment and the area in front of the yard. The densely planted daisies in front of the house resemble a chamomile field.

For the craft you will need:

• Clean plastic bottles (white, green, yellow)
• Candle (lighter)
• Scotch
• Marker
• White paper
• Wire
• Scissors, awl, compass, ruler, pliers

Petals.

Cut off the neck and bottom of the white bottle. Cut the bottle in half and lengthwise to create pieces of plastic. On a piece of white paper, using a compass, draw a round template, the size is adjusted to fit the pieces of plastic. Transfer the template to plastic and cut it out. Draw strips on plastic circles and cut, not reaching the middle 0.5-1 cm. Round the edges and bend them a little over the fire.

Leaves, sepals and stem.

Draw a leaf and sepal on white paper, cut it out and transfer it to a green bottle. Chop the leaves and sepals. Cut the rest of the bottle in a circle into a thin long strip. Wrap the strip around the wire and burn it a little over the fire.

Core.

Cut one convex part from the bottom of a yellow bottle and bend it slightly over the fire

All preparations are ready. The flower is easy to assemble: put the sepals on the wire, then the white petals, round the end of the wire with pliers and glue the yellow center on top. Glue the leaves to the stem as well. Ready!

The flowers come out in medium size and look beautiful in front gardens or flower beds.

Materials:

• Three plastic white bottles
• Yellow cap
• Wire

Technique.

Cut the bottles in half at the expansion point. Cut off the necks of two bottles. Cut all the blanks into petals and round the edges. Insert two bottles alternately into a bottle with a neck, pierce it with an awl and insert a wire, secure with glue. Screw the cap onto the bottle with the neck. Straighten everything out. Chamomile made from plastic bottles!

These daisies turn out to be very large. They decorate personal plots, flower beds, and front gardens. You can see such flowers from afar.

Materials and tools:

• Large white plastic bottles
• Plastic plate
• Strong wire
• Candle or lighter
• Scissors, knife, awl

Step-by-step instruction.

Cut off the necks and bottoms of the bottles. Cut lengthwise and cut petals from these blanks, shape them by slightly bending them over the fire. It’s better to take a yellow plastic plate; if you don’t have one, then you need to paint it first. Use a knife to make holes on the edges of the plate and insert the prepared petals into them. From the inside of the plate, carefully burn the inserted edge of the petal with fire. This will prevent them from falling out. Make a hole in the middle of the plate and thread a wire through it, imitating the stem of a flower. Chamomile is ready!

From the same materials, everyone will get their own beautiful daisy, with its own special twist, which will definitely fit into either the interior of the apartment or the design of the garden plot. And a creation made with your own hands will always please the eye.

Each master uses his own tricks for making daisies from plastic bottles, and some are willing to share them. You can learn a few little tricks from the video master classes:

Video on the topic of the article