How to iron wool trousers. How to iron polyester pants

For a business person, trousers are almost the most important element of the wardrobe. A neat look and impeccably ironed arrows will tell about their owner even more than he can tell about himself. For this reason, it is so important to learn how to iron your trousers correctly in order to feel confident, and your colleagues have only a pleasant impression of you.

How to iron trousers: the necessary technique and work algorithm

In order to qualitatively iron trousers, you will need a good iron and a properly organized place for ironing. Without all this, it will not be possible to get rid of wrinkles and bruises, as well as to make beautiful, even arrows. Ideally, if the iron is equipped with a temperature switch and a steam supply system. If you have an old Soviet iron - it does not matter either. In this case, always use damp gauze folded several times. If you are a happy owner of a vertical steamer, then with its help you will be able to smooth out even the most difficult bruises right on the weight.
Using a special nozzle, you can make smooth arrows without distortions

It is better to iron trousers on an ironing board, but it can be quite successfully replaced by a kitchen table covered with a thick blanket. Auxiliary items will also come in handy:

• iron;
• tailor's pins or stationery clips (binders);
• spray bottle with water;
• terry towel;
• sheets of cardboard or thick paper.

Pants, like other types of clothing, are recommended to be ironed inside out or through an iron. This will protect the fabric from the formation of las, shine and tan. Pins and clips are useful when ironing the arrows, as they are used to fasten the crotch and side seams. A spray bottle is used to additionally moisten the fabric so that the folds are ironed out better, and a terry towel facilitates the process of ironing some hard-to-reach places. A sheet of cardboard is placed under the burlap of pockets or seams so that they do not print on the outside of the trousers after ironing.
To iron trousers, you will need an iron, ironing board, ironing iron and clips.

Temperature conditions for ironing trousers from different fabrics

Before you start ironing, you need to read the information on the label. The composition of the fabric and care instructions should be indicated there. Depending on the material, you need to choose the optimal temperature regime.
The label shows pictograms indicating ironing options and product care

Knowing the composition of the fabric, it will be easier to choose the right temperature on the thermostat:

• wool, mixed fabric - wool mode, number 2 or two dots;
• polyester - silk, nylon mode, number 1 or one dot;
• cotton, linen - cotton, linen mode, number 3 or three dots;
• cotton + synthetics - iron like wool, but with pressure.

Wool is not ironed with pressure, but steamed, barely touching the fabric with the sole of the iron. Cotton and linen are pressed with pressure using a damp iron. Synthetic fabrics are ironed at a minimum temperature only through gauze. If it was not possible to determine the composition of the fabric, then ironing begins from the inside out at the hem of the trousers.

Also consider the type of fabric. If there is a pile, then the product is ironed, if possible, only from the reverse side. If this is not enough, then the iron is led in the direction of the pile, that is, from top to bottom, slightly touching the surface of the fabric.

Algorithm for ironing classic trousers with arrows

Pants are ironed in the following sequence:

1. Turn inside out.
2. First, iron the upper part: burlap pockets, under them.
   Burlap trousers are ironed from the inside
3. So that the trousers fit well on the figure and do not wrinkle at the seams, iron the side and step seams. The side seam is ironed from the belt down, the step seam is from the bottom of the trousers up.
4. Pants turn out on the face.
5. Unzip the zipper, open its different sides and iron the middle seam. Stroke in the buttocks.
   To iron the middle seam of the trousers, you need to open the zipper
6. The belt is ironed first on the front half, and then on the back.
   The waistband of the trousers is ironed from the outside
7. If there are folds that turn into arrows, then we also pay attention to them.
8. Iron side and back pockets.
   Side pockets iron from the front side by pulling the pants over the ironing board
9. They put a folded towel inside the trousers or put it on the edge of the board.
10. Iron the codpiece and the front of the trousers.
    The codpiece is ironed with the nose of the iron
11. Fold the trousers in half and begin to form arrows.
12. after finishing work, the trousers are allowed to cool for 15 minutes, and preferably several hours.

How to make creases on pants

For an inexperienced hostess or a single man, it is quite difficult to iron perfectly even arrows. If you do not want to spend money on dry cleaning every time, you should learn all the tricks of impeccable ironing. There are two important points here: how to fold the legs correctly and where, in fact, these arrows should be located.

How to fold trousers correctly and where the arrows should be

For the formation of flawless arrows without distortions, it is important to fold the trousers correctly. The product is folded in half along the middle seam. The legs are aligned so that the step seams completely coincide with the side seams. Make sure that the lines of the side seams coincide in the upper part of the trousers (look along the edges of the belt). If the trousers are cut correctly, then when the seams are aligned, the front arrow will start exactly at the end of the front tuck or pleat.
To properly form the arrows, you need to fold the trousers correctly

The arrows, as it were, “cut” the front and back halves of the trousers into two equal parts. Depending on the model of the trousers on the front, they may begin with a tuck or a pleat. If the pants have two folds, then the fold that is closer to the codpiece turns into an arrow. As for the back half, there the arrow ends somewhere at the level of the end of the back tuck or the inner edge of the pocket, but does not reach the waist. The back half of the trousers is always ironed after the first. On it, the arrow is formed quite easily, but only after you have ironed the front one correctly.

Photo gallery: where the arrows are located on different models of men's and women's trousers

In these trousers, the front pleats turn into creases The creases start at the ends of the front darts The creases in the front begin with a crease Many models of women's trousers also have creases

Is there a difference between ironing women's and men's trousers with arrows

There is no significant difference in ironing female and male models. Ironing takes place according to the same algorithm: first they iron from the inside, then the upper part from the “face” and finally proceed to the formation of arrows. The difference can only be in the technique of ironing. Women's trousers can be narrowed down or almost adjacent. In this case, when ironing the internal seams, a folded terry towel is put inside the trouser leg or the same trouser leg is pulled onto the board for ironing the sleeves. They do this in order not to break the fold line of the arrow and not to make a fold from the inside.

You also need to take into account the fact that not all models of women's trousers have arrows that reach the waist.
Arrows on women's trousers visually lengthen the legs

How to iron the arrows correctly

So, you have done half the work and it remains only to iron the arrows. Do the following:

1. Fold the trousers in half, align along the crotch and side seams.
2. Fasten the trousers at the waist with a clip or pins (if the fabric is not too thin and will not show holes).
   It is better to fasten the belt of trousers with the help of clerical clips
3. Turn the top leg out to the side.
   The arrows are ironed on each leg separately
4. Fasten at the bottom, once again checking the coincidence of the seam line.
   With the help of clerical clips, you can fix the bottom of the trousers and then the seams will not come apart during ironing
5. If the trousers are lined, then do not forget to move it as far as possible.
6. Cover the bottom leg with an iron and moisten with water from a spray bottle.
   The ironing net greatly facilitates the process of forming creases on trousers.
7. “Mark” the line of the front arrow: apply the iron in turn, first in the knee area, then in the upper part and, finally, in the lower part.
8. After that, boldly iron the arrows from top to bottom, slightly pulling the leg with your free hand.
   First, iron the arrow on the front half of the trousers
9. Iron the crotch.
10. Proceed to form the back arrow in the same way, only ironing should be in the opposite direction - from the bottom up.
    The arrow on the back half of the trousers is ironed only after the arrow has been made on the front.
11. Turn the leg over to the other side and iron it again.
12. Let the trouser leg cool slightly (15 minutes).
13. Flip the pants over to the other side so that the un-ironed part is on the surface and the ironed part is off to the side.
14. Form the arrows in the same way.
15. Fold the trousers in half so that both legs lie on top of each other, and iron again on both sides.
    To fix the result, both halves of the trousers are ironed together.
16. Let the product cool down for an hour.
17. Hang your trousers on a hanger or put them on.

The iron can be omitted if you have a high-quality steam iron with a ceramic sole, and the fabric from which the trousers are sewn lends itself well to wet-heat treatment and is resistant to shine.

How to save creases on trousers until washing

The formation of smooth, beautiful arrows without "doubling" and distortions is a painstaking and skill-requiring task. Therefore, it is natural to want to keep this effect at least until the next wash. There are several tricks that will help fix the arrows for a long time:

1. A bar of soap. Soap draw a line of arrows from the inside. Then the product is turned inside out and ironed with steam.
2. Vinegar solution. For a liter of water, you need a tablespoon of vinegar. The solution is sprayed with an iron or poured into a tank of water and ironed with "acetic" steam. The bend of the arrows is clear, even and resistant to deformation.
3. starch solution. Take a teaspoon of potato or corn starch per liter of cold water. Boil on fire for 2 minutes and then allow to cool to room temperature. In the resulting solution, the iron is moistened. Use only for linen and cotton fabrics of light shades.

By the way, a solution of vinegar prevents the appearance of shine and las on the fabric. Thus, by using vinegar in shaping the creases, you also protect your trousers from unsightly shiny stains.

Video: how to iron creases on trousers and how to make them durable

Correcting ironing errors: lasses, tan marks, double arrows

Unfortunately, we often forget to use the iron and unsightly shiny spots remain on the fabric. Fortunately, in most cases, these problems can be fixed.

How to remove glare and shine

Lasas are shiny traces from the sole of the iron. They are most noticeable on dark fabrics made from natural, mixed and synthetic fibers. The problem is fixed in the following ways:

1. If the fabric is made of cotton or linen, then the laces are almost always removed by steaming through a damp iron.
2. If the fabric is mixed, then you will need to prepare a solution of water, vinegar and a few drops of liquid soap. Moisten gauze in the solution and iron the problem area through it until the stain disappears completely.
3. Ammonia will help to remove gloss from woolen fabrics. A few drops of ammonia are diluted in a liter of water. Then proceed in the same way as in the first method.
4. Las on synthetic fabrics is removed with gasoline. A cotton pad is moistened in the product, and then the stain is treated with it. After this treatment, the product is washed and dried naturally.
5. Shine from dark suit fabrics is also removed with unsweetened black tea: a cotton swab is moistened and the stain is treated.
6. You can also wash the trousers again, and add fabric softener when rinsing.

If it was not possible to eliminate the lasses on your own, then you should take the pants to dry cleaning. In the case of synthetic fabrics, it also happens that the shine from the iron remains. In this case, the pants are ruined forever.

Video: how to remove iron shine from trousers

How to remove burn marks from an iron

Burn marks are yellow spots that are most noticeable on white, light and colored fabrics. Eliminating them is more difficult than lases. For this purpose, the following methods are used:

1. Lemon and powdered sugar. The stain is rubbed with a slice of lemon and sprinkled with powdered sugar. Allow it to dry, and then partially wash the treated area or wash the product completely.
2. Onion porridge. Onion gruel is applied to the place with tan and left to dry completely. Then wash and dry as usual. You can also use onion halves, which carefully rub the stains.
3. Vinegar and salt. Make a solution of 9% vinegar and water in equal proportions. A place with a tan is moistened in a solution, and then sprinkled with salt. After the fabric has dried, the product is washed.
4. 3% hydrogen peroxide. Use only on white fabrics. Peroxide is applied to a cotton swab and treated with a tan area. After the treated area dries, it is rinsed in cold water.

If you are unsure of your abilities and are afraid to ruin your pants completely, then immediately contact the dry cleaner.

From the first time it is not always possible to make the correct single arrows. If, during ironing, the trousers slid along the ironing surface, then it is quite likely that double arrows will form, which will obviously not please the one who is going to wear these trousers. Fortunately, it is much easier to remove "homemade" arrows than stable industrial ones formed under a special press. Do the following:

1. Turn pants inside out.
2. Arrange so that the arrows are in the middle of the leg.
3. Moisten the gauze well and place it on the problem area.
4. Iron until the arrows disappear.

The disadvantage of this method is that, most likely, you will also get rid of the “factory” arrow and it will have to be re-formed. We advise you to first try to fold the trousers correctly so that the seams match, and then iron well with steam. Perhaps the extra arrow will disappear. You can also wash your trousers, and then try to iron them better.
You can try to eliminate the extra arrow by ironing through a wet cloth.

According to the laws of etiquette, shirt sleeves are ironed without arrows, and classic men's trousers are properly ironed with arrows. This cheat sheet will reveal all the secrets of ironing men's trousers:

How to iron trousers

1. Before ironing men's trousers, you should pay attention to the label - it contains recommendations on the mode of ironing the product. Ironing temperature for each type of fabric is different! see table
2. Lay the trousers on a flat surface: on an ironing board, on the floor or on a table covered with a blanket.
3. Turn the pants inside out and iron the lining, waistband, pockets on the inside.
4. Turn right side out and position the legs so that the side seams match, that is, they lie exactly on top of each other.
5. Fix the position with safety pins or threads.
6. Turn pockets inside out to avoid unnecessary folds.
7. Bend the trouser leg lying on top.
8. Iron arrows first - see .
9. Cover the leg with a damp cotton cloth/gauze and iron. Set your iron to steam for best results.
10. Repeat the same steps with the second leg.
11. Be sure to let the trousers cool on a hanger so that they do not wrinkle.

Top Tips:

Before ironing men's trousers, pay attention to the label - it contains recommendations for ironing the product. Ironing temperature for each type of fabric is different! Cm.

Use special tools that will facilitate the daily ritual of ironing trousers.

It is important not to carry the iron over the fabric, but to rearrange it, focusing on the area of ​​\u200b\u200bthe arrows.

The crease on the trousers will last longer if, before ironing, rub the fabric from the inside exactly along the crease line with dry soap.

You need to iron the trousers on the front side through a rag.

Pants with arrows are the main feature of the classic pantsuit. Beautifully smoothed, smooth arrows are the hallmark of a business person. After all, they talk about the severity, business qualities of a partner and his concern for his appearance. But often making smooth, neat arrows is a rather difficult task. Let's take a look at how to properly iron the creases on trousers.

Ironing steps

In order for the ironing process to be as effective as possible and without consequences for the product, proper preparation is necessary. There are several features that can help you avoid mistakes during ironing.

First of all, you need to prepare all the necessary tools and equipment:

After that, you need to study the product label located in the belt area. Thanks to the information on it, you can find out about the composition of the fabric and possible ways to care for the product.

Artificial (synthetic) and natural fabrics are ironed with different heating temperatures of the iron sole. Wool, linen, and cotton can withstand high temperatures, while nylon, polyester, and silk need a little heat, otherwise they risk glossing and scorching.

Pockets must be freed from the objects contained in them, and the outer surface of the trousers should be inspected for contamination and, if necessary, cleaned with a brush to clean the pile and hairs.

Only clean trousers can be ironed, as exposure to temperature can provoke the strengthening of dirt. After smoothing, small spots will penetrate deep into the fibers, and then it will be difficult or impossible to remove them later. So if you need to wash the product or remove stains, then these procedures must be carried out in advance.

At the initial stage of ironing, the pants must be turned inside out, and then ironed from the front. At the same time, the sole of the iron was perfectly clean, and there was always a piece of thin fabric at hand, since without it it is impossible to iron the legs well and make arrows. Direct contact of the iron with the material of the product may cause scorch marks and shine. It is better to prefer white fabrics for ironing to avoid staining the trousers.

And it's also no secret that wet fabric is smoothed better, unlike dry and overdried. Therefore, during operation, the iron should be moistened with water as often as possible and use the steam function of the iron or use a spray gun.

Having completed all the preparatory work, you can begin the process of smoothing the product.

Formation of straight arrows

So, after completing the main stage, you can begin to form arrows on the trousers. Rules for smoothing arrows:

1. Before ironing the arrows on the product, you need to make sure that the side seams of the legs match exactly. And also check that the arrows continue to tuck - to prevent their twisting and displacement.
2. For convenience, you can fix the line of arrows using pins. But this should be done very carefully so that puffs and punctures do not form. And in the process of ironing, make sure that the sole of the iron does not fall on the pins, otherwise marks on the fabric cannot be avoided.
3. You can use an alternative fixation option - laying a basting seam along the arrow. Although this procedure is longer in time, but without risk to the material of the product. At the end of ironing, the basting must be removed.
4. Next, cover the ironing areas with an iron and start smoothing the arrows. There are two ways to do this:

• simultaneously form arrows on two legs;
• step by step to carry out the arrows on each leg.

The easiest way is to start ironing from the knees, moving towards the edges.. The fold lines of the fabric should be pulled slightly with your free hand. In order not to displace the prepared arrow, perform pressing movements with an iron with steam. This method is ideal for synthetic fabrics.

After ironing, allow the product to cool and dry, and then hang it in a closet or put it on for wear. Otherwise, there is a risk of rapid wrinkling of the material of the pants.

Tricks to get perfect arrows

There are several popular ways, thanks to which you can get smooth, non-wrinkling arrows for a long time:

1. With a pointed piece of laundry soap, smear the inner line of the arrow and only then begin to smooth them.
2. Wet the iron with a solution of vinegar instead of plain water. A tablespoon of vinegar added to a liter of water will prevent shine and also provide additional fixation to the hands.

If the first time you did not succeed exactly, then the result can be corrected. In order to remove sloppy arrows from the trousers, you need to do the following:

Thus, having correctly completed all the stages of ironing, you can not only make beautiful arrows on men's trousers, but also forget about shiny and tan marks forever. And resorting to some tricks - form neat arrows for a long time.

Attention, only TODAY!

The most important part of the business wardrobe for both men and women is trousers. Often classic models require proper care. It is difficult to imagine a strict outfit without trousers with perfectly ironed arrows, and we are talking about this today. Let's figure out how to properly iron trousers with arrows after washing, so that the arrows look like new. Science is not easy, but mastering it is real. It just takes a little patience and perseverance.

The history of arrows

The development of the clothing industry took place in the middle of the 19th century. At that moment, pants began to be sewn in factories and factories. The long journey from the manufacturer to retail outlets contributed to the fact that in tightly packed boxes, products acquired a fold at the point of inflection. The person who allowed himself such an expensive purchase flaunted these folds-arrows for a long time to show others that the wardrobe item was new, in other words, “from the needle”. Over time, it was noticed that the pleats on the trousers give the owner a slim, respectable and well-groomed appearance.

So the fashion for classic trousers with thin and even arrows came into fashion. The festive outfit was systematically updated, armed with an iron.

How to prepare your pants

To begin with, you need to properly organize the workplace.

• Install an ironing board, and if it was not on the farm, then it is permissible to use any horizontal surface: floor, closet, chest of drawers, sofa or table.

Important! If you use an unsuitable coating, then be sure to protect it by covering it with a cloth in several layers.

• Before you start ironing, pay attention to the label on the product. It should be written there that the fabric retains the ability to wrinkle under the influence of high temperatures.

• If you have an ordinary iron without steam and additional functions, use a protective material in the form of any thin fabric or gauze.
• Inexperienced housewives prepare pins in advance, with which they pin the legs to the board in order to fix them motionlessly and, accordingly, iron them correctly.
• It is better if the material of the product is wet. This will help prevent the item from returning to its original position after ironing.
• The temperature depends on the information about the composition of the fabric, which is indicated on the label of the product.
• For insurance: natural fabrics are ironed at high temperatures, and synthetics at low or medium.
• First, turn the garment inside out and smooth out any wrinkles.
• Having completed all the preparations, you can start leveling from the “face”.

How to smooth wrinkles

The style of men's trousers is significantly different from women's. In the latter case, the use of tucks is provided. They visually slim, emphasizing all the curves of the female figure. In addition, for the convenience of women, they make: straight, narrow and cropped trousers.

If you need to quickly solve the problem of how to iron trousers with arrows, all the features of the wardrobe item are taken into account. Preparation of things for ironing is identical for all men's models.

Women's styles

Iron the product from the inside. At the same time, do not disregard such complex elements as tucks, pockets, belt. The next instruction is:

1. Turn pants right side out and lay flat on a flat surface.
2. Women's skinny trousers are stacked so that not only the fold line is connected, but also the darts.
3. To keep the thing lying evenly, attach it with pins.
4. Lay damp gauze over the fabric.
5. Start ironing.
6. Once you have finished ironing the first leg, carefully move it aside and iron the second leg.

How to properly iron male models

Initially, it is better to iron all difficult areas - pockets, zipper areas and belts. It's best to do it from the inside out. The execution scheme is the same as for female models. The difference is that men's don't have darts. If a male novice takes up the case, it is better to see a photo or video of the process before starting.

Important! Periodically use a spray bottle to moisten the fabric. Please note that an even fold is a rather long occupation, and under the influence of high temperatures the gauze dries quickly. It is better to constantly keep it moistened.

Where are the arrows

Pay attention to a number of rules where it is better to place beautiful kinks on the legs.

• the fold runs strictly along the shared thread;
• the strip must be in the middle of the knee;
• arrows run along the entire length from the very top to the bottom cut.

How to fold your pants for ironing

• Focus on the position of the crotch and side seams. If the task is to iron the arrows, then try to match the legs as accurately as possible on the sides and bottom cut.
• Make sure that the outer and crotch seams lie clearly on top of each other.
• For reliability and insurance, pin the legs with pins.
• Women's models are much easier to iron, because they have tucks, and for men's options, control and constant attention to the position of the seams are important.

Important! Pins sometimes do not solve the problem of skewed fabric, especially if you are ironing on a curved surface.

How to extend the life of arrows

Even if you tidy up your suit and make perfect folds, the first wash will negate your efforts. To save the result for a long time, you should take an interest in the intricacies of saving arrows. To prolong the life of the arrows, you can easily and simply use folk recipes, their cost is cheap, and the effect is long-term.

• Soap application. Take laundry soap or any remnant and draw along the ironed lines from the wrong side. After that, just iron the legs again from the front.
• Use of starch. In areas of the knees or buttocks (where the folds do not hold well) can be treated with a starch paste from the inside out. After it is completely dry, turn the product inside out and iron it “off the face”.

• Table vinegar. Dilute a tablespoon of vinegar in a liter of water. Soak the cotton fabric in this solution, place it on the clothes and start the ironing process.
• After the end of the procedure, do not immediately put on the product. Let it cool down for 6-7 minutes. In this case, the thing will stay neat longer.
• If you have ironed your trousers in advance, then store them on a hanger, or hang them up without folding them.

Now you already know how to iron perfectly straight lines on your pants, so here are some useful tips for competent ironing or in emergency situations.

• If the fabric on the knees has stretched and lost its shape, then go over the fabric with a damp cloth with tangential movements. Return them to their original shape, and only then iron them.
• If the material is natural, then sew the arrows with thread before washing. That way they won't fall apart. Stroke in the usual way.
• The crease on the leg, remaining after lengthening, you can try to remove with wet gauze. Iron inside out to prevent shininess. Set the maximum allowable temperature for a certain type of fabric. Place the iron on the gauze and wait for it to dry completely. If necessary, repeat the procedure for the complete disappearance of the crease.

The fact that I meet people by their clothes has long been known from folk wisdom. If you properly steam and iron your pants, you will look like a needle. Ideal arrows add a plus for karma in the eyes of others, and double or fuzzy arrows will spoil the opinion of you. The acquired knowledge and constant practice will help keep the wardrobe in order.

Video: How to iron the arrows on the pants

Pants are one of the important details of both women's and men's wardrobe. Their ironing is a laborious process.

To do without outside help, everyone should know how to properly iron trousers.

Preparatory activities

How to iron trousers with or without arrows?

Before you start ironing, you need to prepare:

1. Find a place to iron. If you are going to process the product on the table, then cover it with a dense light-colored cloth. If available, cover it with a special cover, or cover it with a thick blanket. In order not to spoil the product, spread a small piece of gauze on top.
2. Heat the iron to the temperature indicated on the pants label. The best option would be to have a steamer, because without this function it will not be possible to make beautiful and even arrows. Also prepare a container of water or a spray bottle.
3. Turn the product inside out and place on the ironing surface.

When ironing clothes, use a thin cloth or gauze, especially for natural materials (wool, silk or cotton).

Step by step ironing process

Once you have prepared everything you need, you can begin the ironing process.

Instructions on how to iron trousers:

1. First of all, you need to iron out all the details that are on the lining, as well as pockets and a belt. Then turn the pants right side out.
2. Next, you need to smooth the top of the product. In this case, a special pillow will help. It is placed under individual pieces of clothing.
3. Let's move on to the trousers. Fold the front and inside seams to each other. They must match exactly. Smooth them out on one side using the steam function. Then repeat the manipulations on the other side. Fold down the top leg and iron it from the inside. Repeat with the second part.

Arrows at this stage still do not need to be done. Remember that every area you work on must be covered with gauze.

The gauze should always be slightly damp, if you do not follow this recommendation, then the end result will be spoiled.

Working on arrows

How to iron creases on trousers? After the trousers have been ironed, you can proceed to the execution of the arrows.

The work is as follows:

1. Before you start ironing, find the darts. They are both on the back and on the front of the leg. Secure the tuck with a pin on the ironing surface, smooth the legs along the edge. Make sure both legs match at the seams and undercuts. And only after that start fastening them with pins.
2. Cover the product with gauze. Then you need to iron the arrows on the trousers. To do this, use the steam function.
3. Leave the pressed trousers with creases on the table to cool.

After 15-20 minutes, the ironed pants can be put on or put away in the closet, hanging them on a coat hanger.

Fixing arrows

A person, in addition to ironing trousers with arrows, needs to know what to do so that the arrows can hold on.

Experienced housewives give some important tips:

1. How to smooth out creases on trousers? To make the arrows better fixed, the water in the spray bottle can be diluted with table vinegar or ammonia.
2. Soap will help to smooth the arrows on the trousers and fix them for a long time. To do this, turn the pants on the wrong side and rub soap on the line along which the arrow will be smoothed. After this step, the leg is ironed.

Correctly ironing pants with arrows is not so difficult if you follow all the tips.

Ways to eliminate arrows

How to iron pants with arrows? Not everyone succeeds in making the intended arrows exactly, which, as a result, greatly spoils the appearance of the product. Then another question arises, how to quickly remove them on ironed pants?

There is a way out of the situation, for this:

• turn the pants inside out;
• set the same temperature on the iron that was used to create the arrows;
• well, using the spray gun or the steam function.

It is not always possible to fix the problem the first time, so you may have to repeat the steps several times.

Experienced housewives identify several rules for proper ironing:

1. Purity. During ironing, the high temperature from the iron acts on the item and dirt particles penetrate even deeper into the fabric fibers. Then getting rid of the stains will be even more difficult. Therefore, so that stains do not appear on ironed trousers, they must first be washed.
2. The composition of the material and the heating of the iron. The ironing temperature depends on the type of fabric. , wool, silk, cotton are smoothed using completely different technologies. To determine the desired temperature, located in the area of ​​\u200b\u200bthe seams of the product.
3. Ironer. If you do not know how to properly iron men's trousers, then there is nothing to worry about. The main thing is to have a small piece of cloth on hand that will protect against direct exposure to the high temperature of the iron. It's called the ironer. It can be made of gauze or white cotton fabric.
4. The wrong side. Before making arrows, men and women need to turn the product with an arrow on the wrong side. This will help prevent shine.
5. Spraying with water. A wet product is better for the ironing process. Therefore, you should always have a container of water or a spray bottle at hand. Better yet, get a steamer or steam generator.

After that, the smoothed thing is placed in the closet on a coat hanger.

Pointing arrows on your pants is not easy. Sometimes this process takes a long time. But every time a skill appears, after which ironing is no longer considered such a tedious task.