home › Health and beauty › Make a plane out of A4 sheet. How to make a paper airplane that flies for a long time: model options, step-by-step diagrams, photos and videos

Make a plane out of A4 sheet. How to make a paper airplane that flies for a long time: model options, step-by-step diagrams, photos and videos

Peculiarities: a model capable of covering a decent distance at a good speed. It only takes five steps to fold the plane.

Difficulty level: short.

2. Flying hunter

Peculiarities: the aircraft has a weighted nose, due to which the flight range will increase. To set a record, you need to launch the "hunter" with maximum strength.

Difficulty level: average.

3. Sprinter

Peculiarities: this plane can be called a "jet", it flies very fast. There is room for experimentation: try folding the wings at different angles.

Difficulty level: average.

4. Spear

Peculiarities: a model designed for long-distance flights, like a spear. Requires precision when folding.

Difficulty level: average.

5. Phoenix

Peculiarities: a great plane that can be launched with any force. If you follow the instructions exactly, flying will always be easy.

Difficulty level: average.

6. Dart

Peculiarities: model of complex design, similar to a dart. The extra fold in the nose gives it more weight and longer range.

Difficulty level: high.

7. Bird

Peculiarities: original model, reminiscent of a swift or swallow. It flies very fast.

Difficulty level: high.

8. Fighter

Peculiarities: a model that repeats the appearance of a navy fighter. Folding is hard, but worth it.

Difficulty level: high.

9. Starship

Peculiarities: this space-like airplane is suitable for acrobatic etudes in the air. If you throw it straight ahead, it will flip over.

Difficulty level: expert.

10. Sea wind

Peculiarities: this plane will glide through the air because of its raised wing. You can run the model even with a little effort.

Difficulty level: expert.

For more instructions on making original paper planes, see.

In childhood, everyone was fond of throwing a paper airplane to each other. Many adults remember such entertainment only with the advent of children, when the basic skills for collecting complex origami crafts are already lost. To please and occupy your child for a while, learn how to make a paper airplane according to a simple pattern, teach crafts to fly, what you need to fold the model.

How to make paper airplanes

The art of aerogami has been around for over 50 years. During this time, craftsmen were able to come up with and skillfully bring to life hundreds of different models of paper planes. Some of them fly for a short time and only along one trajectory, but there are those that are able to cover long distances. Modern designs of the boomerang or the unusual Glider appeared.

How to glue a paper plane

A thick A4 sheet, a ruler, glue, scissors and possibly felt-tip pens - this is all you need to glue a paper plane with your own hands. It will be good if you find a ready-made drawing on the Internet in advance and simply print the drawing. If a dotted line is indicated in the photo, this is the place of the fold. The arrows on the sketch indicate the turn of the paper in a certain direction, and the straight lines indicate the place of the cut.

origami planes

It will be easier for beginners to assemble a glider model from common materials: A4 sheets, thin paper, notebook sheets or newspaper clippings. The main requirement for the material is that it should resemble a square or rectangle in shape. To make an origami plane, you just need to follow clear instructions. There is one more little trick: in order for the parts to keep their shape better, aerogami professionals recommend drawing along the fold with a ruler.

How to make a paper plane - step by step instructions

In order for the assembled model to keep its shape well and not fall apart from touch, you need to take a few tips into service:

It is optimal to use sheets of small size with a density of 100g/m².
During operation, you must strictly follow the instructions, iron the bends well and fold the material according to the scheme.
To launch a paper plane, it is important that all the details are symmetrical. Especially for balance, you need to pay attention to the bow and tail.

simple airplane

When teaching aerogamy to children, it is better to start with the development of simple models. The way to make a classic layout is as follows:

Prepare a landscape sheet. Turn it towards you with the short side.
Fold the sheet in half and mark the middle of the sheet. The crease does not need to be smoothed out.
Unfold the paper and fold its edges so that the corners touch the marked center line.
Grasp the top of the sheet so that the junction of the two folded corners becomes its fold.
Fold the top left corner in the same way. Repeat the same action with the upper right corner.
A triangle should have formed, bend it up.
Fold the model in half. Form the wings.

Airplane

This model is almost the same as the assembly method from the previous version, the only difference is the blunt nose. To assemble an airplane airplane, follow these instructions:

With a sheet of thick paper, do the first 4 steps from the instructions above.
Bend the upper left and right corner so that a straight line remains in the center, 0.8-1.5 cm long.
Secure the part with the bottom triangle.
Turn the model inside out along the center fold.
Straighten all parts, set the desired angle of the wing.

Paraglider

Thanks to the wide wings, this model can soar beautifully in the air. To make an airplane out of a sheet of paper, you need to follow the tips:

Bend and unfold the rectangular sheet lengthwise as always.
Measure about ¼ from the top and wrap towards the center.
Bend both corners inward so that their noses do not go beyond the intended line.
Flip the model over and fold the folded half over.
Bend and fold the small corners in the center.
Bend the model along the central fold, unfold the nose and form the wings.

small plane

The dimensions of this model are small, so get ready to do painstaking work. How to make a paper airplane:

Take any sheet of paper measuring 20 * 20 cm.
Fold in half, iron the fold.
Fold in half again to form a square. Mark the center.
Fold one half of the paper onto ¼ of the sheet, make a note.
Bend the sheet inward from the ¼ mark and to the top edge, you get a triangle. Smooth the edge.
Turn the edge outward so that a small triangle forms at the top.
Turn the sheet over, bend the other side of the triangle inward.
Bend the wide end towards the pocket, a few millimeters short of the edge.
Do the same with the other side.
Put the fingers of one hand under the fuselage, fix the nose of the aircraft with the other. Lift the paper slightly with your hands.
Fold the corner into a pocket. Repeat the previous two steps on the other side of the sheet.
Fold up the side of the large pocket. Do the same on the other side.
Open the model, bend its front edge inward.
Turn the workpiece over, push the front part, using the corners as a guide.
Fold the plane in half, go through the folds.
Fold one side down along a line that is parallel to the center fold.
Do the same on the other side.
Fold the edge of the wing up for better aerodynamics. Straighten the model with your hands.

big plane

This model can decorate a children's room. To fold the liner, prepare cardboard, glue, scissors, a matchbox and follow the instructions:

Cut a long strip of cardboard 2 cm wide. Fold it in half.
Fix the edges with glue in the center of the matchbox top and bottom.
Cut two strips of cardboard 4 cm wide. Round off the edges.
Glue to the matchbox on the sides.
Cut out a thin strip of cardboard and fold it in half.
Wrap the edges of the strip up, indenting from the edge by 1 cm.
Glue the workpiece to the tail.

square plane

Many are accustomed to seeing flying machines with a pointed nose, but not all models may look like this. Try folding the paper airplane differently:

Unfold a piece of paper with the wide side facing you. Fold in half.
Turn the sheet over to the other side, with the narrow side facing you. Fold in half.
Turn the sheet to the other side. Fold the edge towards the center of the fold.
Fold in the corners on both sides.
Flip the paper over with the folded side facing you. Fold the edge to the center.
Fold the plane along the center perpendicular line.
Fold over the folded edge. Open the pocket, holding the center with your fingers.
Expand the pocket. Bend the wings to the triangle marked in the center.

volumetric aircraft

After you have mastered simple models, you need to learn to understand more complex schemes. Below is a step-by-step instruction on how to assemble a volumetric flying plane:

Bend the sheet lengthwise, unfold.
Fold the paper in half. From the center, fold the edges down, and then unfold half.
Unbend the sides from the side, tuck each lapel inward.
Bend part of the wings back.
Bend the wings from the bottom a short distance.
Press the fold lines with your fingers. Bend the resulting lines parallel to the folds of the wings.

beautiful plane

You can decorate a children's room with paper crafts by collecting a whole collection of different models. To make flying machines pleasing to the eye, they can be made of colored paper or cardboard, decorated with applications - numbers, inscriptions or asterisks. Three-dimensional models of passenger liners look good on a shelf in a nursery. It will take a little more time to make them.

How to make a passenger plane out of paper

To create this model, you must download and print the Concorde airliner assembly diagram in advance. Then, to fold the passenger plane, follow the instructions:

Make folds in the center and top corners.
Fold the side parts to the middle, then bend their edges back along the dotted line.
Fold the shape right side up along the center line.
Bend the corner along line 5, smooth it out, and then return the figure to its original position.
Repeat the same on the other side.
Tuck the edge inside the case along the dotted line, then pulling its end back and bending along line 6.
Bend both wings up, fix the tail with tape.

How to make a cool paper plane

There are also such models of devices that are able to gently plan for a long time or fly over long distances. They are slightly different in design from their simple counterparts. If you want the airplane to fly further, choose a model with narrow wings and a long tail. Balanced airplanes with a large wingspan are capable of long flights.

How to make a paper plane that flies

If you get bored with the basics of aircraft construction, try making a cool model with good aerodynamics:

Make a midline and fold the corners around the edges.
Fold the product across exactly in the center, turn it over.
Under a slight slope, fold the corners, not reaching a little to the fold.
Wrap the resulting angle, straighten the part bent on the other side of the aircraft.
Fold the model along the base, form wings at the same distance.
Make small bends of the wings along the edges.

How to make a paper plane that flies far

This design provides for the formation of additional wings in the nose of the apparatus, which will ensure the flight range. To make a paper airplane, follow the instructions:

Mark the center line, fold the edges to it at an angle of 90 degrees.
Turn the workpiece over, bend the corners towards the center again so that a sharp edge forms in the center.
Raise the triangle at the back, and fold the resulting square in half.
Mark the crease with a pencil, fill the rectangle in the middle of the pocket.
Bend the wings at a 90 degree angle.

How to make a military plane out of paper

Boys who are fond of war games, shooting games and armored vehicles will love the idea of creating a collection of military aircraft at home. There are a lot of models of such aircraft. You can fold the Fighter, Bomber, Il-2, Messerschmitt or other equipment. To make such toys look colorful and be as similar as possible to the original, it is recommended to make them from colored paper.

Fighter

Options for making such paper toys can be found on the Internet, or you can make a paper fighter according to the following scheme:

Take a rectangular sheet. Fold in half along the widest part.
Bend two corners towards you.
Bend the corners again diagonally, starting the movement of the hand from the sharp nose.
Fold the product across so that the sharp part is in the center of the opposite side.
Turn the paper over, fold the top edges down.
Wrap the resulting corner on yourself.
Bend the shape in half. Form the wings and flaps of the aircraft.

bomber aircraft

This beautiful model is a little more difficult to create, but the result is worth the time spent. To make it work, follow the tips:

Fold the top of the sheet into a double triangle.
By analogy, bend the left corner, aligning the top of the sheet with the right side.
Make a fold of paper that will pass through the intersection point of all the resulting lines.
Fold the side triangles along it inward.
Mark a center line at the bottom of the sheet.
Mark a line that is parallel to the base of the triangle.
Flip the paper over to the other side.
Bend the corner towards you.
Turn the layout over again and bend the two corners up, tucking the top half in half.
Turn the figure over, bend the corner.
Fold the right and left edge which is inside the layout.
Bend the corner away from you, fold the plane along the central bend.
Bring the edges inward, fold the figure in half, and then turn it on yourself.

long-haul aircraft

This model will be able to overcome any distance. It has good aerodynamics, is well balanced and weighs little. Long-haul aircraft do this:

Make notes of the center of the sheet, bend the upper corners.
Fold the sheet in half, forming a roof with sharp corners.
Fold the edges of future wings inward to further sharpen the nose.
The layout is turned down with the front side, then the wrong side is folded vertically. without touching the bottom corners.
The wing is bent so that it captures the entire length of the workpiece.
Set the wings to the desired angle of inclination.

Video

Hi guys! In this article, we will talk about how to make paper plane 100 meters flight . Generally speaking, almost any aircraft can fly far enough - it all depends on the height from which it was launched. The design features of paper planes affect their ability to glide. So a plane that can plan for a long time will fly very long and far from a height, for example, 16 floors. The wind will additionally help speed up and extend the flight of such paper crafts. Let's start our rating of the farthest flying aircraft.

5th place - the simplest paper airplane models

In this place are all the simple models of aircraft that even a child can assemble and which we all collected in the lessons and let girls and teachers. For such tasks, ordinary blunt-nosed aircraft and gliders are quite suitable. Here are 10 of the best paper airplanes that are easy to build.

This is the simplest and most popular paper airplane - almost all people know it, because they have been collecting it since childhood.

The following aircraft model has a fast and uniform flight. Due to the front supporting wings, the nose does not collapse, providing stabilization, lift and long flight.

Next will be a blunt-nosed aircraft with increased resistance to collisions.

The fifth will assemble a modified aircraft with a blunt nose. The scheme is simple, but requires accuracy when assembling.

Now I propose to assemble a good paper plane with nose wings and vertical rear stabilizers. The shape of the wing of such a glider allows you to fly longer in a straight line.

The next plane has a sharp nose and flies fast forward. The ribs on the wings stabilize and prolong the flight of such a paper fighter.

The following scheme has good piercing abilities - the craft turns out to be similar to a space fighter. It seems that it was created to destroy the manpower of the enemy.

The glider has the largest wings, which has a rather ridiculous appearance. But this does not prevent him from flying very long and far.

The amazing design of this airplane makes it look like a space shuttle or a Boeing. He flies not far, but effectively.

4th place - paper plane "Albatross"

We bend a sheet of A4 paper in half and draw with a fingernail so that the fold is perfect.

We bend the edges of the paper inward to the central axis.

After that, we bend the edges with an obtuse angle again to the center. The edges of the paper should lie symmetrically on the central axis of our craft.

Then we bend the nose of the paper plane towards the tail and combine the centers of symmetry.

Add corner folds so that the left side is parallel to the right side.

We unbend back and bend the sharp nose of the aircraft back along the flight path. We iron all seams with nails.

We bend the wings so that a large area of \u200b\u200bthe wings remains bearing. We do everything extremely symmetrically so that the plane flies further.

At the end we form a tail. In principle, the bend of the tail can be done as in the photo of any size.

We straighten the resulting bends up so that it is in the space between the wings.

We bend the vertical stabilizers upwards parallel to the main axis of symmetry of the paper airplane. Here we have such a plane - rather try to launch it.

If you have any questions about the assembly of this aircraft, then watch the detailed video with comments.

3rd place - a diagram of an airplane made of paper "Hawk"

Now we will assemble another complex aircraft.

First step. We bend the sheet in half exactly in the middle. The quality of the flight will depend on the evenness of the folds. All stages of the aircraft are mirrored - left and right.

Second step. We bend the left and right sides to the center.

The third step - once again we take the left and right edges of the paper and fold them to the central axis of the aircraft.

The fourth step - we bend the sharp end of the workpiece towards the tail. In this case, the fold line of the sheet should pass through the intersection point of the edges in the middle of the paper craft. Centering is checked by matching the central bend along the long side of the sheet.

Fifth step. The edges of the paper on the left and right are again bent to the center, as in the photo. It is important here that the inner layer of paper does not bend or form folds.

Sixth step. We grab the outer fold and open it, and then wrap it inward as shown in the photo. Do the same on the other side of the plane. We take the formed pockets and bend them inside out.

Seventh step. The pointed nose needs to be bent in the opposite direction about 1 cm deeper than the logical fold line. Pockets are formed there, which we bend inside the nose from about the middle.

Step eight. We also wrap the tip opposite the sharp nose.

Ninth step. We bend the wings of the aircraft from paper parallel to the keel. If the wings of your paper craft are the same, then the base of the aircraft is assembled symmetrically.

Tenth step. In parallel to the main axis of symmetry, we bend the edges of the wings to make the flaps. The plane is ready.

A detailed video on assembling such an aircraft with your own hands from paper is given below.

2nd place - a diagram of an airplane made of paper "Thunderstorm"

We will continue to assemble a paper plane that will fly for a long time according to the scheme of high assembly complexity. We will need, as always, a sheet of A4 paper. It can be plain white or colored paper. You can also take sheets from magazines with medium paper weight.

The first step is to bend the sheet in half. We remind you - from how smoothly and symmetrically your aircraft is assembled, it will fly in the same way. After bending the sheet in half, unbend it and then proceed to the second step.

The second step - we bend the corners to the center - on one side and on the other. It turns out such a preparation.

Third step. The edges of the paper, which formed an obtuse angle on the left, are correctly bent again along the line of the nose of the aircraft to the right angles of the paper blank. See how it looks in the photo. Straighten the folds of paper near the nose especially carefully so that everything is symmetrical.

Fourth step. We see a point at the intersection of the bends of the left and right edges of the workpiece. Along the line through this point, you need to fold the airplane in half, as shown in the photo. You can check yourself by matching the lines of the central fold. After folding, unfold, turn over and bend in the opposite direction.

Fifth step. Turn the plane over again and fold the left and right sides to the edge of the inner sheet. See photos and videos for more details.

After that, turn the plane over again and bend the nose forward again.

We turn over again and turn the strip of folded paper to the tail of the aircraft blank.

Sixth step. We bend the plane along the central longitudinal axis. It is convenient to bend the stabilizers on the wings in this position parallel to one side and the other.

Seventh step. We bend the wings to the base. Here you can bend in different ways and experiment, but it is considered optimal - bending from the nose to the fender liner.

Everything should converge exactly and be symmetrical. Then the paper plane will fly exactly 100 meters or more and not fall to the left or right.

If the plane will fly down, then you need to bend the back of the wings slightly up. Thus, the flow of oncoming air will lower the tail of the aircraft, and lift the nose up.

1st place - a diagram of an airplane made of paper "Falcon"

This is probably one of the most beautiful paper planes that you can make with your own hands, because it is very similar to the real one. To fold such a long-flying aircraft with your own hands, follow the detailed instructions with photos and videos at the end.

1 - take a sheet of medium density A4 paper and fold the sheet in half to get a plane out of paper.

2 - we bend a sheet of paper in half for the longest flying paper plane.

3 - we break the paper along the edges to make a cool aircraft with our own hands.

4 - we bend the second side also at the airplane from a sheet of paper.

5 - Iron the resulting paper airplane corners in half again.

6 - open each wing of the aircraft and deploy them.

A variety of toys and crafts can be created with your own hands. Many of them will take 3-5 minutes to create a beautiful thing or a cute trinket that kids can play with. A paper plane is one of the options for such items. In this case, you can use your imagination to create not just a semblance of an aircraft, but a full-fledged three-dimensional layout. This will require paints, felt-tip pens or pencils, and even drawings.

A variety of toys and crafts you can create with your own hands

Origami is not just a way to create cute crafts and funny paper toys, but a full-fledged art direction. The classic version of the creation assumes that the airplane will be folded from a single sheet of special paper (you don’t have to glue or cut anything). The creation scheme is simple: you need a rectangular sheet that will be transformed into a nose (the front of the future airplane), its body, wings and a tail will also be present. So, detailed instructions and folding scheme step by step:

Stages of work:

Put a sheet of origami - paper on the table, fold it vertically in half;
Then the sheet will need to be expanded;
After that, you need to fold the two upper edges to the center of the sheet (do not expand);
Fold the same corners again so that they connect, but do not intersect on the center line (do not unfold);
Bend the upper sides down to the right and left;
Raise the left and right sides to form the wings.

The plane is ready to fly.

Gallery: pictures of a paper plane (25 photos)

Paper plane (video)

Big paper plane

You can create a large fighter plane from A4 paper. For children, it will become an interesting toy, for adults - a way to relax, show imagination. You will need to start work by preparing the place and paper (it can be plain white or color, light office or cardboard).

Stages of creation:

Bend the sheet in half lengthwise;
Then bend in half horizontally again;
Fold the corners so that they meet in the center;
Bend them up;
Starting from the middle of the fold, fold the side corners;
Unfold the folded paper at the top;
Then expand all corners;
After that, fold the upper part of the triangles in half, starting work from the lower corners;
The sides of the paper should be folded slightly towards the center;
After that, fold the sides to the middle of the sheet;
The side parts of the resulting rhombuses must be tucked so that a triangle is obtained;
Then it should be folded in half vertically;
Tilt the craft to the left, bend a parallel line, stepping back 1-2 cm;
The resulting wing is bent down (right and left);
Then the moving part of the wing will need to be folded in the middle on each side.

You can create a large fighter plane from A4 paper

Such a toy will fly quickly and smoothly. An unusual option will allow you to come up with various situations and game moments for tricks.

How to fold a flying plane: a simple diagram for children

It will be very interesting to fold your own paper toy for a child. That is why it is important to choose an assembly scheme that he can easily reproduce. Flying models of a paper airplane will help him not only develop his creative abilities, but also develop fine and gross motor skills.

It will be very interesting to fold your own paper toy for a child.

In order to assemble your first aircraft, you will need to perform a few simple steps:

Take plain paper (you can use a notebook sheet);
Make a square out of it (fold the lower part and tear off along the line);
Fold the resulting sheet in half;
Bend the upper edges to the center of the sheet;
Bend the resulting paper triangle;
The edges of the workpiece are again bent towards the middle;
Then the sheet is bent in half and the corners are bent, forming wings.

Such a sharp-nosed aircraft will fly very fast.

How to make a paper swallow

If the creation of a paper plane does not interest the child, then you can offer him to fold the birds. Swallow is an easy version of such a craft.

To create it, do the following:

Take a regular sheet from a notebook;
Bend the upper left corner to the right to the middle;
The rectangular part of the sheet formed below must be carefully torn off, but not thrown away, since this part will still be needed in the work;
Fold a square sheet diagonally (you should get 2 lines intersecting in the center;
The resulting paper pyramid should be folded in half so that a triangle is obtained;
Its left corner must be bent up;
Do the same with the right corner;
The left side then needs to be bent down;
Repeat the operation with the right side;
The rectangular part should be folded vertically in half (this is the tail);
Bend the upper left corner to the center;
Repeat the action with the right corner;
Insert the part in the middle of the main part of the craft.

If the creation of a paper plane does not interest the child, then you can offer him to fold the birds

Bend the nose of the swallow.

Cool do-it-yourself paper plane

Cool military models of flying vehicles can be created in stages not only from plastic or wood, but also from accessible materials such as plasticine or paper.

You can easily make any kind of aircraft:

Bomber;
Fighter;
Space;
Supersonic.

Cool military models of flying vehicles can be created not only from plastic or wood

In order to make the figurines as realistic as possible, you will need to use several colors of paper or felt-tip pens to color them.

For the bomber you will need:

Rectangular sheet of paper (A 4);
Its upper corners must be bent to the center;
Then unbend them, mark a line next to them to bend the corners to them;
After that, bend and unbend the corners on both sides;
Fold the resulting figure in half;
Draw a line from the side in the center, bend the edge to it (on each side);
Bend part of the corner on each side;
Bend up also on each side;
Turn the workpiece over, then bend the edges to the center on each side.

Bend the corners and fold in half. Bend the wings of the aircraft in front and behind.

How to make an airplane out of paper

What paper is an airplane made of? To create a paper airplane, you will need colored or white paper. It is important to choose one that is not too heavy for work, since in this case the craft will be able to fly quite smoothly and quickly. For even greater realism, you can draw certain details of the airplane.

For work you will need:

Take a sheet of paper, medium in density;
Fold it in half, then unfold;
Bend the corner towards the center to form a square;
Tear off (carefully) the bottom of the sheet - do not throw away;
Bend the top corner in half (you get a triangle);
Expand the resulting figure and bend the bottom corner up (one);
Bend the upper corner to the center of the craft so that it goes beyond it .;
Then fold part of the corner (side) in half;
After that, bend the corner up and to the side;
Also do with the second corner of the future airplane;
Expand the figure, bend the upper corner inward (nose);
After that, bend outward its uppermost part;
Expand wings.

The airplane is ready to fly. You can supplement the model by gluing to it in the middle the torn part of the sheet folded in three in half.

Aircraft with a catapult (video)

Thus, paper planes are not limited to simple models. Existing schemes, supplemented by fantasy, will allow you to create a real paper fleet: passenger and military, fighter and glider. Bright and varied models are obtained from colored paper, crafts designed to decorate the interior, for example, in a nursery - from cardboard.

(40 ratings, average: 5,00 out of 5)

Most adults know how to make a paper airplane and it's quite a useful skill in raising a child, but not everyone has the knowledge to create multiple types of airplanes. I think it's not a secret for anyone that children at an early age are very fond of doing something with their own hands and entertainment with origami will allow you to keep your child busy for a long time.

Moreover, the cost of origami classes is completely miserable - any paper, wallpaper or even thick cardboard is suitable for assembling your aircraft.

Airplanes are free

Considering that there are always old notebooks in the house, paper damaged in the printer, old wallpaper rolls, newspapers, magazines or something like that, you will always have a free opportunity to keep your child busy with interesting things. Actually, this is the first advantage of creating paper airplanes - you do not spend money on making your child happy with an interesting activity, entertainment that brings joy and benefit.

In comparison with the development of an airplane out of paper, buying a designer for the same purposes looks like an incredibly expensive undertaking, you must agree.

The benefits of origami

In addition to the cheapness of this lesson, it is also worth understanding that working with your hands has a very positive effect on the development of the child - he begins to think better logically, improves visual memory, begins to think figuratively, remembers volumes and instructions.

This is a chic practice for a child, which allows at home, with little or no additional control, to give the younger generation the opportunity to train their memory and visual images. this is especially useful at the age of 4 to 9 years, when the child is still interested and can already independently think through the steps, work with visual images, come up with their own versions of the model and work with ready-made instructions from the net or needlework magazines.

Plus, the child will develop a desire to do everything perfectly - if you tell a child how to make a flying plane out of paper in sufficient detail, he will try and make his own model.

It may not turn out to be very successful, in this situation it is worth encouraging the future engineer and let the child try again, having previously thought through the mistakes that he made when modeling the previous version.

Maybe the paper at the joints was not thick enough, maybe the nose or wings of the aircraft were not well thought out and air resistance prevented the aircraft from moving as far as possible. All these points can be thought through together, making it clear what problems there are and what options for solving them in origami, for example, can be used.

Illustrative examples of airplanes

Although in childhood we all made airplanes of various types and shapes, not everything remains in your memory and certain areas of the design have long been erased from your subconscious, plus most of the models, I am sure, you have never seen and do not know how to build them. To do this, you can find a photo of a paper airplane on the Internet and choose some interesting options that may suit you.

It should be understood that if you have just started doing this, then there will be certain difficulties in understanding the process of working with paper, that is, you must first choose the simplest models - a classic airplane, for example, which is assembled in a minute.

After working with this model for a long time and improving it, you can move on to more complex models - there is an airplane called "Arrow" or "Jet" that allows you to complicate your task and get a more interesting model with a longer flight duration.

paper airplane competition

You will be surprised, but in the world there really are competitions for launching paper airplanes into the air - they are held on an ongoing basis with cash prizes and television coverage, so there is a real motivation to do this and the process itself can be called serious, because adults also play in the competitions with a fairly decent experience of working on the launch of airplanes.

Of course, no one tells you to take a child and prepare him for a competition right now, maybe you don’t need it at all, but you can arrange competitions among yourself, in a family or between families if you find yourself partners for the battle.

For example, we take the classic instructions for assembling an aircraft - we take a sheet of A4 paper, preferably more or less dense, bend it in half along the long side, then bend the upper corners to the middle of the sheet, the sharp ends need to be bent, again, in half and bend the whole structure along in the middle, then it remains only to clearly highlight the wings and you can launch the airplane into battle.

Try to hold competitions among yourself on this model of the aircraft, see how it flies, what subtleties of the design you noticed, then take a more complex model and work on it

colored airplanes

An airplane made of white paper looks solid, but if you are already a pro and want to get even more pleasure from flying, then be sure to buy colored paper or just take magazines with color pictures and collect airplanes from this paper, then you will have more vivid emotions and joy from process.

And, of course, there is always something to grow - there are dozens of aircraft assembly instructions on the Internet, you can try them all and evaluate your design capabilities. Good luck, I think you will definitely enjoy this activity!