Is it possible to increase the size of a diamond ring. Important facts and nuances: how to roll out a ring at home

The reason for this action may be related to wrong choice jewelry size. Perhaps someone simply did not know the size and could not find the right ring. It happens that the hand has recovered or, conversely, at the time of purchase it was swollen, swollen, and then lost weight. But is it difficult to fit the product in size? And what is the best way to do it?

Simple and safe option with boring

It is quite possible to increase the size of a ring with a stone in the simplest and safest way - through boring the product. This procedure involves sawing the inner layer of the shank. It allows you to enlarge your ring by about half the size. The method is ideal for products with decorative and precious stones having a wide shank.

The process is usually carried out using special machine with latch. He is not suitable for too thin rings. Only for wide. Takes approximately 10-30 minutes. However, this method has its downsides. Due to the use of rolling or boring, the thickness of the shank will decrease. It will become thinner than its original thickness.

Increasing the size by rolling

There is another simple option that allows you to increase the size of a wedding ring or any other product. It means rolling metal. It is performed using special equipment, a machine. As in the case of boring, it is necessary to narrow the shank of the ring. IN this case it will also become narrower, and the size of the ring itself will increase.

Metal inserts

To increase the size of the ring, you can use inserts from suitable metal. In the process of work, the master carefully cuts the shank from below (in the place where it touches the finger). And then he begins to push it as far as it will be necessary to increase the decoration in size. For example, if you need to increase the product by one size, you need to expand it by about 3.14 mm.

The resulting space is covered with a small piece of metal, completely suitable in terms of parameters and appearance to the ring itself. At the same time, the joints are treated not only with a laser, but also with fire. For decoration natural shine it is necessary to immerse it in a solution with boric acid. After that, you won’t even be able to distinguish where the original metal patch is located, and where the factory shank begins.

The type of soldering directly depends on existing form stone on the product. It is possible to increase the size of the ring by soldering an insert made of identical metal in at least an hour. Sometimes it takes more time to process a product.

Using the Pinocchio tool

To increase the size of a piece of jewelry, an apparatus called "Pinocchio" is often used. During the procedure, they usually put a ring on it and begin to stretch it due to an increase in the size of the cone. However, before increasing the size of the ring with Pinocchio, it is necessary to heat the product. Otherwise, you risk tearing the jewelry or deforming it.

According to experts, this option is perfect for working with wedding rings and products of the most ordinary rounded shape. On average, such work does not take more than 25-30 minutes.

The use of mechanical stretching of metal

Answering the question of whether it is possible to increase the size of the ring, one cannot but recall the method of mechanical stretching of the metal. However, the method is not suitable for products with complex decorative patterns. The presence of a small stone in this case is allowed. The ring itself should also not be too wide. Its approximate thickness should not be more than 10 mm.

In the process of work, the master usually performs calculations, determines the size. After that, he rotates the fixed decoration on a special crossbar and heats it up. Thus, he manages to achieve suitable dimensions of the product. At the end of the procedure, it is necessary to eliminate roughness and uneven areas of the tavern. To do this, it is cleaned and polished.

Making a metal insert without sawing

In the course of work, the master uses an additional metal plate made of a similar metal. Or instead of it, he uses an additional ring inserted inside your product. This method, according to jewelers, is considered the most expensive. However, it does not have any physical effect on the main decoration. All resizing work is carried out with the used internal inserts. As a result, it is not the ring itself that changes, but its inner diameter.

How to increase the size of the ring at home

Changing the size of a product is not as easy as it might seem at first glance. Therefore, in most cases, experts recommend not even trying. There is a huge risk that you will spoil the product. In such cases, it is best to contact specialists.

However, if you are still determined, you will need the following tools to get the job done:

• Special bolt.
• Gas-burner.
• Small rubber mallet.

But keep in mind that having all these tools does not give any guarantee that you will succeed. First you need to take the ring and clamp it, for example, in pliers or round nose pliers. Then you need to turn on the burner and heat the product to a characteristic red color. Next, leave the decoration for a few minutes to cool down a bit. And when it is slightly warm, it remains to insert it into the crossbar and start rolling.

What products can be rolled

Before rolling, please note that not all products can be processed in a similar way. For example, you cannot use rolling for rings with rotating inserts. Not worth trying this method and for bimetallic products. It is not recommended to roll out and in the presence of inscriptions, engravings and drawings.

If your rings contain stones, they must be carefully removed before the procedure. Otherwise, when the ring is stretched, they may leave their “nests” and jump out. At the end of the work, you can return the stones back and fix them securely, using round nose pliers, for example.

Be careful!

Be careful! Lest the phrase "The miser pays twice" apply to you, don't skimp. If you have a product that is not suitable in size, but is very expensive for you, give it to professionals. Let the work cost money, but it will preserve the appearance of your jewelry.

Precious metal rings are the most popular gifts for women. Having received such a gift from a loved one unpleasant surprise is the wrong size. And sometimes the decoration just becomes not enough for you. And then the question arises of how to stretch the ring at home. WITH possible options We will solve this problem in this article.

Determine the correct size

Of course, it is best when buying such an expensive gift know Exact size or better yet, buy it in the presence of a lady of the heart. In this case, you need to keep in mind that the fingers may swell in the morning, especially in hot weather. It may also happen after physical activity, as well as at elevated temperature during illness.

Important! The thickness of the fingers on the left and right hand is different.

If you don’t know the exact size, then you can calculate it in simple ways at home:

• A strip 1 cm wide is inserted inside the product. A pencil mark is made in the place where one of the edges ends. The length of the marked strip is measured with a ruler. The resulting number is divided by 3.14 - this will be the size of the jewelry.
• Most exact way at home - measure the inner diameter with a caliper, it's just that not everyone has it.
• You can measure it with coins if you have them: 1 ruble - size 21, 50 kopecks - size 19.5, 5 kopecks - 19, 10 kopecks - 18, 1 kopeck - size 16.
• The easiest, but not the most accurate, is to measure the size of the ring with a ruler, while taking the inner diameter.

We take into account the features of different jewelry

The most accurate way is to contact a jeweler or jewelry store.

As you can see, the risk of spoiling the jewelry is very high, so the most reliable way- Go to a jewelery shop.

If you need to change the ring size, please consider the following points:

Important! Repair of platinum products can only be carried out using special expensive equipment, not every workshop can afford it, and therefore the price will be higher, respectively.

Can the ring be stretched?

If you still got caught by buying a piece of jewelry that is not the right size, but it cannot be returned or exchanged, then what should you do? How to expand Golden ring at home?

It's not as easy as it seems. What can be done in such a situation?

1. Need to find a metal cone right size. Thoroughly clean and sand it.
2. Wrap the cone in foil. This is to ensure that there are no scratches on the product.
3. Warm up the ring well and put it on the cone.
4. Carefully tapping the end of the cone with a hammer, we are trying to expand the product.

Ring stretching methods

Since the way to expand the ring at home is not the easiest and gives guaranteed result Let's turn to the professionals. If there are stones on the jewelry, then they will need to be temporarily removed so as not to accidentally break or deform. There are 4 stretching methods.

rolling

The ring is rolled to the desired size on a special tool. This method is only suitable for sufficiently thick products. Thin decoration - may not survive and just break.

Inserting a piece of material:

1. The ring is cut in one place, usually near the sample.
2. A piece of metal of the same quality and sample is inserted into the place of the cut so that the fragment does not differ in appearance.
3. The place of soldering is welded. The seam is not visible to the naked eye, its thickness does not exceed 0.1 mm

Boring

This is a method in which a piece of metal is ground down inside the piece of jewelry. Appearance the product is not changed.

Stretching with Pinocchio

"Pinocchio" is special device in the form of a cone, on which the decoration is put on. Before processing, the ring is heated and stretched onto a cone.

In a number of stores in St. Petersburg " jewelry network 585" has jewelry workshops where you can repair jewelry, as well as carry out professional care after them. Our stores work experienced jewelers who are well versed in jewelry and will be able to repair jewelry dear to your heart.

Shops in St. Petersburg with jewelry workshops:

* In cases where a master's precious metal is used to perform repairs, the cost of 1 g of 585 gold is 1,500 rubles.

From precious metal, it will take about 10 minutes. This procedure is simple and is usually done with you. It is important that the jewelry falls into the hands of a skilled jeweler. Here is what you need to know about this procedure.

Gemstones require special attention when adjusting the size of a gemstone ring. For example, the most "gifted" and favorite stone "with meaning" is a diamond. But when heated, when the ring is reduced or enlarged, in order to avoid trouble, it is better to remove the insert from the base of the ring. Even if it's a solid diamond.

If you see that the master begins work without removing the stone from the base, stop him and demand it. Make it cost a little more. Remember the miser pays twice

How to reduce the size of the ring

Cutting a piece of shank. The procedure is most often carried out on rings with stones, where it is important not to damage the overall structure. To reduce the ring by one size, a piece of shank (base) about 3.14 mm long is cut out, and the joint is ground and polished.

Knocking the shank of the ring. The ring is put on the crossbar, and then the metal is heated and knocked down. This method is recommended for adjusting the size of simple rings without stones and decorative elements. This is how classic wedding rings are customized. If the ring needs to be reduced by half a size, the ring is not heated, but simply knocked down. When a size or two, the metal is heated gradually and knocked down to the desired parameters.

Reducing the size. Shrinkage of the ring shank when heated

Insert without cutting. In inner part rings insert an additional base metal plate or another additional ring. This is one of the most expensive methods. With such a correction, signs of impact on the ring are excluded, only the internalproduct diameter.

How to increase the ring size

Ring bore. Sawed out inner layer taverns. This is the simplest and painless way Enlarge the ring by half a size. Boring- sometimes the only way to increase the size of the ring is with a thick shank, stones and decorative elements without damage.

Increasing the size of the ring with a thick shank

Mechanical stretching of metal. Suitable for increasing the size of classic rings without inserts and stones, more often engagement rings. In this case, the ring should not be too wide, about 10mm. First, the jeweler calculates the size by which the ring needs to be enlarged, and then, by heating and rotating it on the crossbar, reaches the desired parameters. Cleaning and polishing the ring at the end of the work completely eliminates the presence of traces of exposure. But this method is not suitable for rings that are too thin, they can simply burst.

Metal insert. When the elements of the ring (complex stone setting, ornament) have a high artistic value, the only way increase its size - make an insert from a similar metal. The ring is cut from below, expanded to the desired size, an insert made of the same metal (similar sample, color and shade) is soldered. For shine and gloss, even before the procedure, the ring is immersed in a solution boric acid. As a result, you will not distinguish a corrected ring from a new one.

At the end of all procedures, the master polishes the ring and the stone itself. Then he wipes it with napkins soaked in a special solution.

Polishing and daily cleaning of jewelry

Ideally, if such services are not needed. To do this, it is better to try on a hundred times, and only then make the final choice.!

Instruction

Gold has excellent plasticity, so if necessary, the size of a gold ring can be relatively easily changed by reducing or increasing by one or two sizes. Perform this operation even if there is suitable tools not recommended because in the wrong hands jewelry may be irreversibly deformed.

The most common way to increase the size of the ring is mechanical. The master first checks what the true size of the product is, and then determines by what amount it is necessary to increase it. After measurements, the ring is treated with a burner flame. When it cools down, the product is put on a special crossbar. With the help of a roller corresponding to the profile of the product, the ring is stretched to the required size. It remains to align the ends and grind the ring to its original shine.

There is a more time-consuming way to increase the size of the ring. In this case, it is increased by inserting a piece of metal of a similar sample. First, a joint is formed, where a piece of material is applied and carefully soldered when heated with a heater flame. The updated product is then bleached, dried and carefully processed with a jewelry file to remove possible protrusions and depressions.

When choosing a specific method, experts always proceed from the size of the ring. For thin product most a simple one will do mechanical stretching. If the ring is massive and thick, it is easier and more reliable to use the insertion method. In the simplest case, when the ring needs to be enlarged by just a fraction of a millimeter, sometimes it is simply bored inner surface removing the thinnest layer of metal.

If the ring has inserts in the form of stones, they are often dismantled before work. This is done in order to reduce the risk of stresses appearing in the stone, which may well lead to its irreparable deformation. After increasing the size of the ring, the stones are easily inserted into their places, securing them accordingly.

The wedding ring is a symbol of marriage, so spouses wear it on ring finger right hand as a sign of loyalty to each other. However, there are situations that require an increase in its size. As a rule, the traditional marriage ring consists of gold, which has plasticity. Thus, it will not be difficult for a jeweler to change such an important piece of jewelry by one or two sizes.

Undoubtedly, the complexity of the work is determined directly by the master and it depends specifically on the type of wedding ring: smooth or with stones. It should be borne in mind that the pricing policy of each individual company is diverse, so you need to contact only those specialists who do not raise any doubts about their professionalism and competence. Otherwise such important element marriage union risks being damaged irretrievably.

The main ways to increase the size of a wedding ring are: stretching this metal on a crossbar, as well as inserting a piece of gold of the same standard. First of all, the jeweler determines the exact size of the ring, after which he determines how much the product should be enlarged. Then, the master anneals the ring with the flame of a special burner, and when it cools down a little, he puts a crossbar on the stretching roller prepared in the roller. After that, a roller is installed, which in shape corresponds to the profile of the gold jewelry. Further, the jeweler, rotating the handle of the crossbar, moves the guide axis and, accordingly, the clamping handle, and free hand he presses the roller against the ring, trying to fit it onto the crossbar. Thus, when the ring acquires right size, the master will wash it, bleach it and level the ends of the ring. In the end, the product is polished, thereby acquiring the original luster.

In the event that the decoration is enlarged by inserting a piece of gold, then you need to impose small fragments of this metal in without fail of the same sample to the joint, and then solder them under the flame of the burner. Then jewel the inserted piece is bleached, dried and adjusted so that there are no protrusions and depressions. It should be noted that if wedding ring thin, then best method changes in its size will be mechanical stretching. In contrast, a thick ring tends to be difficult to stretch, so inserting a piece of gold is advisable.

The increase in the gold ring having stones is mainly carried out an experienced craftsman in the following sequence: removes the stone from the fixture, performs certain procedures with this metal in order to change the size, and then inserts the stone back. It must be remembered that increasing the size of the ring with a stone will cost the client much more.

Related videos